How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
In this article down the page yow will discover more first-rate help and advice related to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is readily obtainable, the job can move speedily; if you need to open a wall surface to remove the old bathtub as well as place the new bath tub, the job is much harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to think about employing one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your shower room if you have actually already gotten a new tub and also do not need to alter the setup of your previous supply of water pipes.
Your devices and also material list need to comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the installing opening in the bath/basin making certain that the washers are in area between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap connectors. The previous type needs to be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the tub in the required placement. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four small factors.
The next goal is to ensure that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub up until the level checks out degree.
To install taps, fit the bottom of the outermost flexible faucet connector to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub as well as additionally check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the bath tub has been used a minimum of when as this will certainly settle it into its final setting.
Planning for the Installation
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to penetrate the wall in between the bath and the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can break rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our part on How to Install a Bathtub. Thank you for taking time to browse our blog. Sharing is good. You won't know, you may very well be doing someone a favor. Thanks for taking the time to read it.
Click Here! Report this page